There are various reasons behind your computer slowing down during startup. However, you can easily deal with these problems to speed up the startup process.

Identifying Which Programs Load Automatically During Startup:

The most common cause of slow computer startup is the number of programs that load when the system starts. You first need to identify which programs load automatically during startup. It may be surprising, but the truth is that a vast number of programs automatically start when your computer boots up.

To identify the programs that load during startup, perform the following steps:

1. Press SHIFT+CTRL+ESC key together to open Task Manager.
2. On the Performance tab, check if the Performance Usage on your computer is higher than the Physical Memory (RAM) of your computer.

This is usually the main reason behind a slow startup. Too many programs running at the same time contribute to a slow and tedious startup and of retarded performance as well.

How to Deal With the Problem:

Now that you know what is creating the problem, you have to stop or disable a few programs from automatically starting up when you boot up your computer. Remember, every program that runs on your computer is, without doubt, slowing down your PC.

To disable unwanted programs from loading at startup, perform the following steps:

1. Go to Start and click Run
2. Type msconfig and press Enter
3. Note: If you are using Windows Vista or Windows 7, type msconfig in the Start Search box and click Enter.
4. Open the Startup tab
5. Here, you will see all the programs that load during system startup. You can disable the ones you know are unnecessary. There may be some programs that need to run at all times- leave these programs enabled. Disable all other unwanted programs by clearing there checkboxes.
6. Once done, click Apply and then OK to apply your changes and exit the System Configuration Utility
7. Restart your computer when prompted.

Don't Keep what You Don't Require:

Always ensure that you don't keep any programs on your computer that you do not use. Although installed software on your PC may not be the direct reason behind your PC slowing down, each program adds entries to the registry and contributes to a slow computer by making the registry bulky.

To remove or uninstall a program:

• Go to START
• Go to Control Panel
• Click on Add or Remove Programs
• Note: In Windows Vista and 7, type uninstall program in the Startup box and press Enter.
• This will populate a list of all the programs that are installed on your system. Once you click on any of the programs, a Remove tab will appear beside it. Select and uninstall the programs you don't need from here. You may have to restart your computer after uninstalling some programs.

Advanced Programs On Old Hardware:

Installing advanced programs on a system you purchased or assembled long ago may also result in slow computing performance as well as slow system startup. It is followed as a thumb rule to avoid any programs, software, and especially, a version of Windows that is newer than your computer by approximately 18 months.

Your computer may have the power under the hood to run these programs, but the shortfall doesn't happen in a day. After a prolonged period of usage, you will almost certainly notice that your system has slowed. So, in such a case, it is best to try to install an older version of the program you want to use. You may also need to revert to the previous version, if the program allows, but this is not a guaranteed process of enhancing computing performance and system speed.

Use your system wisely. Do not force it to perform beyond its capacity- understand its limitations and performance barriers and upgrade it from time to time.

Source

Oftentimes people do not understand computers and what makes them fast or slow, what "memory" is, and how to upgrade their system. The main three components of a basic system are as follows:

Hard drive space - This refers to how much storage space is on your computer to hold software programs. This is where everything on your computer is stored for when you might use it. So you might have a system with 500 Gigabytes (GB), which is pretty normal these days and is usually more than enough for most users. Hardrive space is "memory" in a sense, but it is different than RAM, which is often what the term "memory" is referring to. Your amount of hard drive space also has nothing to do with your computer's speed, only how much "stuff" you can keep on it.

CPU - This is your central processing unit, or the thing that does all the number crunching. When a program is run (even if it is just Windows), the CPU is what is making it work and making it work fast or slow. You may have a computer that has a 2.7Ghz processor, which means that it can process 2.7M pieces of data per second. Oftentimes people will say their computer has a 2.7 "gig" processor. The faster the processor, the faster and smoother you will be able to run software, but it may be limited by your RAM.

RAM - What is RAM? Short for random access memory, RAM is sort of a temporary storage unit for programs. Remember, everything is stored on your hard drive, whether it is open or not, but RAM is just for programs that are open. The reason is that your hard drive is cluttered with so many programs, that it takes the CPU a long time (relatively speaking of course) to access the program you want and keep it running. RAM is much faster and allows the CPU to access programs many times faster. So you may have a really fast CPU, but it you run out of RAM because you don't have much, your computer may seem very slow if you are doing much at all. If you have plenty of RAM then your processor will be able to perform at its best. Also, if your computer does seem slow, adding more RAM may make a world of difference. If you don't have at least 2GB, you probably need more. Most systems nowadays will come with at least 2GB, but 4GB or more is better.

Source

If you are a regular user of Windows or Mac OSX, you will feel like being lost in a strange world in the first time you install and try Linux as the operating system for your computer. In this article, I will show you some tips to help you get accustomed to the magnificent world of Linux as a beginner.

Choose the right Linux distribution that suits your need and experience

There are already a lot of Linux distributions out there for you to choose and there will be more new distributions created by Linux enthusiasts day after day. But unfortunately, not all Linux distribution can be used by beginners. For Linux newbies, I recommend you to choose popular distributions like Ubuntu or Linux Mint.. These distribution are very user-friendly, easy to install and somewhat similar to normal operating systems like Windows and Apple Mackintosh. When you gain more experience and are willing to explore the new things, you can move to more advanced Linux distributions like Arch Linux or Gentoo.

Do not be afraid of the command line

For an average Linux user, the command line is arguably one of the most frequently used applications. The command line is a very powerful and useful tool, you can do almost all the basic computer tasks on the terminal, such as browsing websites, using it as an online chat client or a mail client, you can even listen to music and watch videos on the terminal as well. By the same token, do not be afraid of the command line, try to learn all the basic commands and use the terminal as frequently as possible and your knowledge about Linux will increase very fast.

You can use Windows software and games on Linux easily

Do not worry that you cannot find an open sourced alternative for your favorite window application. And do not worry that you will have to give up playing video games after switching to Linux as well. The trick is you need to use some special packages like Wine. With Wine, you can play video games and run Windows applications on Linux very easily.

Try to seek help on Linux forums and chat channels

The community of Linux users are very huge, active and friendly. So whenever you encounter a problem with Linux, just drop by a Linux forum and ask questions, people there will be very willing to help newbies. Also, all the Linux distributions usually come with user manuals so do not forget to read these document first.

Source

3D printing is a very fascinating process in the manufacturing world. It isn't a new manufacturing method, but it seems as if it is, as it is only recently becoming much more available to the people and businesses. In fact, 3D printing is a relatively underground process at the moment; however it is gaining serious momentum. This style of manufacturing has a wide variety of materials to choose from; over 60 in fact. 3D printing allows for the creation of virtually anything with virtually no geometrical limits on each design. Organic creations can come out of this manufacturing method, as well as rigid pieces. I want to cover one method of 3D printing in particular, sometimes referred to as infiltration. This method is used only by a company known as X1 with sand, and zcorp.

In a nutshell, this manufacturing process uses 3D printing to create a weak and porous product, which is then dipped in epoxy, wax, or super glue. Whatever chemical or material that the 3D part is dipped in will then fill into the product like water to a sponge. Based on the final product being so porous, it doesn't take much for the wax, epoxy, or super glue to fill in, yielding a reasonably hardened product. Let me cover the full process.

Like all 3D printing processes, a computer image will have to be created in some form of CAD software by an engineer or 3D developer. This computer file will then be sent to the advanced computer on the 3D printer. All 3D printing processes are CAM processes, or computer-aided-manufacturing processes. What does this mean? This means that the computer in the printer will tell the jets exactly where to move, and when to do it. When the 3D printer starts up, it will begin by laying down layers of powdered material on to the build envelope, or the "build table" within the printer. Each layer is around 25 microns thick or so. A human hair has a diameter of 20 microns in many cases. Within each layer, the 3D printing process involves laying down an adhesive chemical to hold the material together in accordance to the 3D blueprint designed earlier. The 3D printing process will repeat as each layer is laid down and fused together until a final 3D printed product comes through. The product is pulled from the build envelope I mentioned earlier, where the excess material powder surrounding the product it is recycled. The product will be covered with excess powder, but it can easily be dusted off. The product that leaves the printer is very weak. It will have a lot of air trapped within it; in fact, up to 40% of the product could consist of air. This means that the product is very porous. To fix the product from crumbling very easily, a process known as infiltration is applied to the product. The product is dipped in epoxy, wax, or superglue to gain integrity. Based off of the porous nature of the product, it will essentially suck up the epoxy, wax, or superglue very easily. This results in a final product of a material like sandstone which is somewhat fragile, but very unique.

Source

Starting with the web browser, you should regularly clear the cookies and the cache. While these won't ever get totally out of hand, they can slow down your web experience and make even the snappiest of PC's seem to run at a snails pace. While speaking on the browser, unnecessary toolbars and addons can cause a decent amount of slowdown as well. They eat up the computers resources while stealing screen space and should be used only if absolutely necessary.

Computers that continue to run slowly, or run other applications slowly as well are more than likely in need of routine maintenance. Virus scans should be run regularly and anti-virus software updated. Viruses can turn a computer into a zombie of sorts and eat resources while mass emailing spam or stealing personal information. Alongside the viruses are their slightly less insidious cousins,adware and malware. These programs are usually slightly less malicious than viruses, but can slow down a computer just as much, if not more.

Computers can also be slowed down by lack of maintenance. Just like a car needs its oil changed, computers need their digital insides tidied up. Every time a computer writes a file to the hard drive it finds an open space big enough to fit the file, writes it in, and then makes a note about where it put the file. As time goes by the computer keeps filling in all the open spaces with files and has to write the files closer and closer to one another. Eventually it can't fit new files in, or an old file that's being changed gets bigger, but has no space next to it to grow. When this happens the computer has to split the one file into several parts and put them wherever it can. It would be like going to the library and trying to check out the latest best seller only to find that the book has been cut up and hidden chapter by chapter around the library. This is known as fragmentation, and defragmenting is its solution.

Sometimes computers also just get old. Hard drives can fill up, and when they do they slow down. What was a top of the line computer six months ago is standard today, and in another six months will be ancient. Newer programs and upgrades are always improving the computing experience, but tat the cost of technology. Upgrading a computers RAM, the computers short-term memory, is one way to keep it up to date and generally slowdown free. Newer computers are even utilizing super fast soldi state hard drives(SSDs) to hold the operating system and then storing the user's documents and files which aren't essential to the system on a conventional hard drive. This allows the computer and its operating system to load much faster than normal, and is a nice trade-off between the speed of these SSDs and their high price tag.

Source

Do you know how to keep your working space protected? Although you may feel that the office poses little danger, a security breach can harm your career and your future in the company.

Keeping your office space secure is a relatively simple task, as long as you get used to a number of easy and highly efficient practices.

Lock Your Computer
Each time that you leave your desk, you are exposing important information that is stored on your computer. Keeping this information safe depends on locking your account and having password protection.

Learn to log off your account each time you leave the desk. Your computer settings will enable you to protect the account with a password. Choose something relatively complex that differs from your birth date or the city that you live in.

Document Password Protection
Apart from protecting your computer with a password, you can also increase the security of important documents that contain sensitive information.

Specific programs and little tools are available for password protection of documents. Make sure that you have added a password to all of the important presentations, calculations and reports that you have spent a lot of time and effort on. Someone may otherwise feel tempted to benefit from your ideas without giving you credit. Minimize the chance of this happening by password protecting your documents.

Back Up Everything
Something can always happen to your office computer. It can be a virus or a simple act of carelessness. Such a problem may result in the loss of vitally important data.

Workplace security involves document backups. You can use an external hard drive or CDs to make copies of all the documents that are exceptionally important. Keep the copies stored in a secure place and use those in the case of an emergency.

Protecting Drawers and Cabinets
Apart from computer protection, you need to focus on keeping all of your drawers and cabinets safe.

A simple, old-fashioned locking mechanism can be sufficient for great document protection. Although it may seem like an act of paranoia you should lock all of the drawers that have printed copies of documents, presentations, contracts and other sensitive information.

Be Careful with Important Documents
A final rule of workplace safety focuses on the manner in which you handle and dispose of sensitive information. Be very careful and think about the best places to store such information.

Print out solely the documents that you will have to carry around and use during presentations and official reports. Everything else should be stored safely on your computer and protected with a password.

When disposing of such documents, it will be wisest to utilize the document shredder. Throwing documents in the waste bin will leave them exposed and available for everyone to go through.

Keeping your work space secured and protected involves several basic precaution measures. Make sure that your computer has a password and lock all of your drawers. Such steps will be sufficient to guarantee your workplace privacy.

Many of today's internet marketers are beating themselves up trying to bring in the traffic they need to their websites and promotions. Well this will be informative and straight to the point on how to do this. We all know without traffic there is no chance of any sales.

How do we bring the traffic to our sites? Well if your just wanting traffic its easy, but, if you want quality targeted traffic that's another story. One way is to compose and write articles, there are dozen's of article directories out there, example; articlecity.com, goarticles.com, articlepool.com and the one your reading from just to name a few. If you are writing content irrelevant to your site that would definitely be a problem.

Research and study your niche keeping in mind product review is what you're looking for. You can learn a great deal from reading these reviews and could fuel the article you want, do not copy and paste. If you don't have a plan from the start, I suggest you get one.

Writing articles is fun and engaging at the same time with the right plan, determination, and with correct information make up the key essentials. Have you considered the entire internet has been compiled of written information? The web is constantly evolving with the exception that it's made up entirely of written information.

Now we can go to many extremes in getting traffic, but without the proper tools or training how do you create the medium of building traffic. Well, search the web and you will find thousands of software products and information in books, services, promotions, containing some of the best are downloadable e-books.

Linking to other websites relevant to yours is a great way to bring targeted traffic your way. If you aren't targeting traffic relevant to your niche than why bother. If you have a site promoting shoes you wouldn't target customers looking for hair products. When you have the right plan and the tools at your fingertips then you can build the traffic.

Traffic doesn't happen overnight, unless you buy it, which is done many times becoming very expensive. We are talking about traffic, through article writing, link building, social networking and many other mediums. There is help from inexpensive university's, online tutorials you name it. No excuses finding the help you need, just search the web.

The most common ways to get free traffic is writing those articles, Twitter, Facebook, Google these social networks are great mediums. Linking to relevant websites can bring in traffic otherwise not tapped into. Don't fall into the trap that traffic comes from just publishing websites. It takes time and effort just keep adding to your combined tools and knowledge and in no time you will see results.